Exhaust Hood Systems
MUA Hood Systems
Untempered
Tempered (Heated)
Exhaust Fans
Supply MUA Fans
Untempered
Tempered
(Heated)
Technical Support
Design/Engineering
How to Spec Your Project
Fire Suppression
Systems
Frequently
Asked Q?
CONTACT
US
Optional
Equipment:
Hood
Components
Baffle Hood Filters
Vapor Proof Lighting
Dampers
Stainless
Steel Polish
About Us
OUR
PROUD HISTORY
Warranty
& Return Policy
Legal
Notice
Privacy
& Security
ULTIMATE
AIRE HOODS
122
Washington Street
Utica,
NY 13502
315-732-5253
800-394-2963
FAX:
315-732-0736
ultairehoods@verizon.net
ULTIMATE
AIRE HOODS
A Pleeter Ventilation
Product, UticaNY
 |
To Exhaust Hoods | ||
| OPTIONAL HOOD COMPONENT PRODUCTS: | |
To MUA Hoods | |
|
To Request Quote Form | ||
We
have the following
components
available
to optimize
the efficiency
and aesthetic
appearance
of your hood installation. Please contact us for details on pricing and specifications for your project. |
 |
UTILITY CABINET | |
| ETL
Listed for integral
side mount on
the UltimateAire
ventilation hood.
Fabricated
of same material
as hood. The
cabinet houses
factory pre-piped
UL Listed fire
suppression system*
and ETL Listed
pre-wired electrical
controls. Pre-wire
package* contains
light switches,
lighted fan control
switches and internal
factory wiring
and components
(starters, relays,
etc.) to reduce
field wiring requirements.
ETL tests confirm
temperatures do
not exceed 120°F
inside the cabinet
during fire condition.
(120°F is
the maximum allowed
storage temperature
for the UL Listed
fire suppression
sytem and the
ETL Listed industrial
control panel.) (*Dimensional restrictions may apply) |
||
|
FRONT PERFORATED SUPPLY PLENUM | |
| Provides low velocity make-up air for the kitchen, discharged in front of the hood. Welded, stainless steel on exposed surfaces; unexposed surfaces made of aluminized metal. Shipped separately, requiring field connection. Insulated to prevent condensation. Perforated diffuser plates for even air distribution. Provides required clearance from limited combustibles per NFPA96 Standards. | ||
|
REMOVABLE ETL Listed HIGH VELOCITY CARTRIDGE FILTERS | |
|
||
|
Stainless Steel ENCLOSURE PANELS | |
| Sized to extend from hood top to ceiling, enclosing pipe and hanging parts. Constructed of stainless steel to match hood. Mounting channel is factory welded to hood for field installation of panels over 11" high. Under 11", factory -welded and integrally installed into hood front and ends. | ||
|
Stainless Steel BACKSPLASH | |
Stainless
Steel Backsplash
sold in sheets
of 48"x84" 20
gauge #3 polish,
shipped with
PVC removable
vinyl protective
covering. Typically
installed from
bottom edge
of hood to the
floor. Conforms
with Health
Department regulations
for non-porous,
easily cleaned
surface. |
||
|
SUPPLY VOLUME DAMPER | |
| Adjustable volume damper assembly to balance air volume levels, adjustable by means of an adjustable screw located on the side of the damper assembly. | ||
|
Stainless Steel END PANELS | |
| Should be used to maximize hood performance and eliminate the effects of cross drafts in kitchen. Units constructed of stainless steel and sized according to hood width and cooking equipment. Exposed edges hemmed for safety and rigidity. | ||
|
EXHAUST FIRE DAMPER | |
| ETL Listed. Installed in exhaust collar. Activated by a UL Listed, 212°F, 10-lb minimum rated fusible link. | ||
|
ELECTRICAL CONTROLS | |
| ETL Listed controls, factory pre-wired with built-in wiring chase for electrical controls on the front face of the hood, designed to avoid penetration of the capture aarea and eliminate an external chaseway. |
